Button setting in orangepi 5

[hcws]

thanks for your works , I meet a problem ,when I set button in orangepi 5 . I don't know how to set pin number；

 +------+-----+----------+--------+---+   OPI5   +---+--------+----------+-----+------+
 | GPIO | wPi |   Name   |  Mode  | V | Physical | V |  Mode  | Name     | wPi | GPIO |
 +------+-----+----------+--------+---+----++----+---+--------+----------+-----+------+
 |      |     |     3.3V |        |   |  1 || 2  |   |        | 5V       |     |      |
 |   47 |   0 |    SDA.5 |     IN | 1 |  3 || 4  |   |        | 5V       |     |      |
 |   46 |   1 |    SCL.5 |     IN | 1 |  5 || 6  |   |        | GND      |     |      |
 |   54 |   2 |    PWM15 |     IN | 1 |  7 || 8  | 0 | IN     | RXD.0    | 3   | 131  |
 |      |     |      GND |        |   |  9 || 10 | 0 | IN     | TXD.0    | 4   | 132  |
 |  138 |   5 |  CAN1_RX |     IN | 1 | 11 || 12 | 1 | IN     | CAN2_TX  | 6   | 29   |
 |  139 |   7 |  CAN1_TX |     IN | 1 | 13 || 14 |   |        | GND      |     |      |
 |   28 |   8 |  CAN2_RX |     IN | 1 | 15 || 16 | 1 | IN     | SDA.1    | 9   | 59   |
 |      |     |     3.3V |        |   | 17 || 18 | 1 | IN     | SCL.1    | 10  | 58   |
 |   49 |  11 | SPI4_TXD |     IN | 1 | 19 || 20 |   |        | GND      |     |      |
 |   48 |  12 | SPI4_RXD |     IN | 1 | 21 || 22 | 1 | IN     | GPIO2_D4 | 13  | 92   |
 |   50 |  14 | SPI4_CLK |     IN | 1 | 23 || 24 | 1 | IN     | SPI4_CS1 | 15  | 52   |
 |      |     |      GND |        |   | 25 || 26 | 1 | IN     | PWM1     | 16  | 35   |
 +------+-----+----------+--------+---+----++----+---+--------+----------+-----+------+
 | GPIO | wPi |   Name   |  Mode  | V | Physical | V |  Mode  | Name     | wPi | GPIO |
 +------+-----+----------+--------+---+   OPI5   +---+--------+----------+-----+------+

Here is my setting, but it didn't works

gsmenu:
  enabled: true
  gpio:
    # RuncamVRX
    left: 3
    right: 4
    up: 6
    down: 13
    center: 15
    # alternative
    # center:
    #   chip: gpiochip3
    #   pin: 1
    rec: 16
    # Ruby

[gilankpam]

Orange pi mapping is different, I forked the repo to support orange pi 3b, not sure if it also supports orange pi 5. I haven't tested yet. Feel free to try, you will need to put the number from GPIO column. gilankpam@3d1b61f

[henkwiedig]

Can you try the alternative config method useing gpiochip and pin ?
Use gpioinfo to get a list of the available gpios

[gilankpam]

@hcws try this gpio config https://github.com/OpenIPC/sbc-groundstations/pull/70/files#diff-2c0feee16147fcaf530c75af32adff75fe5b6e62b2bc6fa14a9107930b066fdc